Sale

EURO+DRIVE® TUNING SYSTEM (FIAT 124 SPIDER/ABARTH)

ECU TUNING
$849.95 $749.95
$749.95

EUROCOMPULSION® is pleased to present the ultimate engine control unit (ECU) upgrade for the FIAT 124 SPIDER/ABARTH. The EURO+DRIVE® Tuning system is available in power-specific variations and is conveniently flashed to the vehicle’s factory ECU through the OBD-II port without any physical modification to the factory ECU. The EURO+DRIVE® functionality puts the control of the engine’s operation at your fingertips and allows for comprehensive tuning calibrations that do not only affect power output but drive-ability, throttle response, consistency and smooths overall power delivery.

The Euro+Drive Tuning System includes a map request of Phase 1 and Phase 2 with any of the tuning options applied. Simply meet the tune requirements to run the tune. Additional map requests of the same Phase tune, but options changed, would be a map revision fee.

For Phase 3 or a Custom Tune see here.

    EURO+DRIVE® TUNING FEATURES (INCLUDED):

    • RAISED REV LIMITER
    • RAISED SPEED LIMITER
    • DOWNPIPE OPTIMIZATION
    • PARK/NEUTRAL REV LIMITER REMOVAL (AUTO TRANS)
    • LAUNCH CONTROL (MANUAL TRANS ONLY)
    • POPS & BANGS (EXHAUST NOISE) (VIDEO FROM ARTBOX. EXHAUST SOUND AND POPS WILL VARY DEPENDING ON YOUR SPECIFIC SETUP.)
    • BURBLES (EXHAUST NOISE) (VIDEO FROM DRIVEN DISTRICTEXHAUST SOUND AND BURBLES WILL VARY DEPENDING ON YOUR SPECIFIC SETUP.
    • DUAL MAP MODE (ABARTH ONLY)

    EURO+DRIVE® CUSTOM TUNING FEATURES (ADDITIONAL CHARGES MAY APPLY):

    • BIGGER TURBO
    • E85 OPTIMIZATION
    • ALTERNATIVE/HIGHER OCTANE FUEL OPTIMIZATION
    • WATER/METHANOL OPTIMIZATION

    EURO+DRIVE® FEATURES:

    • True OBD2 Flash Tuning/Calibrations
    • Use of Genuine OEM Software, Maps, and Protocols
    • Simple User Interface (with online instructions)
    • Storage of 5 maps for convenient map switching (including your stock map)
    • Each Calibration is custom calibrated to your ECU specific file and VIN number
    • Calibrations will include modification calibrations
    • Calibrations will Optimize power, drive-ability, and efficiency 
    • Unparalleled consistent, linear, & smooth power delivery
    • Calibrations will retain OEM tuning logic ( IE self-adaptation) and all safety checks
    • Flashing procedure is easy, safe, and protects against incomplete/incompatible flashes
    • All factory hardware works properly 
    • The EURO+DRIVE® does not hack/manipulate or bypass the factory ECU
    • Full control over all engine parameters by utilizing true factory Calibrations
    • Specially requested Calibrations available (additional fees may apply)
    • 91oct minimal fuel requirement
    • EURO+DRIVE Calibrations are street/AutoX/Track proven with an extremely high ratio of podium finishes
    • No physical removal of ECU is required

    SEE ADDITIONAL TABS FOR MORE INFO

      Read More
      Read Less

      124 ABARTH / SPIDER TESTING & TECHNICAL INFO:

       

      EURO+DRIVE® CALIBRATIONS:

      • ~142.8 WHP STOCK
      • ~180.9 WHP PHASE 1
      • ~200.3 WHP PHASE 2
      • ~223.5 WHP PHASE 2 BIG TURBO (EC 1446+ TURBO UPGRADE)
      • ~PHASE 3 w/E85 or 91/93 OCTANE (Bigger Injectors): This map is designed for those that would like to run an upgraded turbo, but want to extract the most power out of the car. To do so, bigger injectors are required for the full performance of this map and an additional charge for this map will be required. DRAGY and Drag Strip times for this are below.

      *After extensive development and testing on Phase 3 and an upgraded turbo on the 124 and 500 Abarth, we determined that to proceed with higher power numbers, the car needs larger injectors. We are moving forward with the use of both E85 and pump gas on the ATP larger injectors (550cc). 

       

      In the future, customers will receive a Big Turbo Tune (Phase 2 Big Turbo) with the purchase of our larger turbo. This will be designed for the stock injectors. We will also offer a free optimization for E85 or pump gas with the purchase of the ATP injectors from us.

      The full Phase 3 tune will be available to EURO+DRIVE customers for a fee, for those that want the max power and have our bigger injectors.*
       

      Please see your make/model on the Tuning Requirements Page to know what mods are required to run each Phase tune.

       

      EURO+DRIVE® TUNING FEATURES (INCLUDED):

      • RAISED REV LIMITER
      • RAISED SPEED LIMITER
      • CATTED DOWNPIPE / CATLESS DOWNPIPE OPTIMIZATION (AND CEL ELIMINATION)
      • PARK/NEUTRAL REV LIMITER REMOVAL (AUTO TRANS)
      • LAUNCH CONTROL (MANUAL TRANS ONLY)
      • POPS & BANGS (EXHAUST NOISE) (VIDEO FROM ARTBOX YOUTUBE CHANNEL. EXHAUST SOUND AND BURBLES WILL DIFFER DEPENDING ON SET UP.)
      • BURBLES (EXHAUST NOISE) (VIDEO FROM DRIVEN DISTRICT YOUTUBE CHANNEL. EXHAUST SOUND AND BURBLES WILL DIFFER DEPENDING ON SET UP.)
      • DUAL MAP MODE (ABARTH ONLY)

       

       

      EURO+DRIVE® CUSTOM TUNING FEATURES (ADDITIONAL CHARGES MAY APPLY):

      • BIGGER TURBO
      • E85 OPTIMIZATION
      • ALTERNATIVE/HIGHER OCTANE FUEL OPTMIZATION
      • WATER/METHANOL OPTIMIZATION

       

       

      SUPPORTED YEARS:

      • 2017 to Present - AVAILABLE

         

       

      EURO+DRIVE INSTALL | 124 ABARTH / 124 SPIDER (2016+)

      June 24, 2020

       

      The following contains instructions on how to flash the ECU on your 124 Spider or 124 Abarth using our EURO+DRIVE tuning handheld. 

      Vehicle Application for these Instructions:

      • Fiat 124 Abarth/124 Spider (8GMK ECU)  2016+

      FIRST STEPS:

      Familiarize yourself with the instructions before starting.

      Activate your account on the EURO+DRIVE Online Portal. This is where you will upload your ECU files and receive tune files. After purchase, someone from the Tuning Department will set up your account on the portal using the email you provided at the time of purchase. You will receive a first time login notification at this email address. Simply open this email, click the link, and setup your account.

      Make sure you have downloaded the EURO+DRIVE Manager application for PC. This can be found in the instructions folder on the Online Portal, which you have access to. You will need this application to connect your handheld to your computer, and download/upload files to and from the handheld. (This application is only compatible with PC devices).

      Things you may need: OBDII connection cable, EURO+DRIVE handheld, and USB to handheld cable (all provided in package).

      - Installation Tips:

      • Don't Rush! Always allow 5-10 seconds or more between key ON and OFF prompts before confirming.
      • Make sure all aux/external devices are powered off.
      • Keep your doors and trunk closed, this can affect the initial communication for tune writing.

      The EURO+DRIVE handheld can easily be reset and memory erased so that you can transfer to another owner or another vehicle. However, failure to flash your ECU back to stock prior to selling your vehicle, selling your handheld, or bringing your car into the dealership for maintenance will lock your handheld and prevent a memory erase from being executed. In this case, you will be forced to send back your handheld and purchase a replacement handheld for $300, no exceptions.

      Never click the "Erase data" tab without being instructed to do so by someone from our tuning department.

      INSTALLATION:

      - Once you have received your handheld, and also have installed the EURO+DRIVE manager, connect the handheld to your PC, and open the manager software. The handheld will automatically update.

       

      - Once the updating is complete, you are ready to disconnect and go out to your vehicle.

      If your car has been sitting or the battery has been disconnected for a while be sure your battery voltage is above 12.5 Volts. We suggest either hooking up a battery tender the day before reading the car or driving the car for about 30 minutes to ensure the battery is properly charged. This is usually only necessary for cars that have been sitting and are not driven regularly. DO NOT HAVE A BATTERY TENDER HOOKED UP DURING THE READING OR WRITING PROCESS.

      - If you have any aftermarket electronic items, like a larger sub or light kits, connected to ignition power or hot power it may be wise to disconnect them during the write procedure. This will help avoid voltage drop issues.

      Step 1 - Connect the provided OBDII cable to your handheld. Ensure you have a solid connection. Then connect the cable to your OBDII port within the vehicle.

      Step 2 - Once the EURO+DRIVE screen is powered up, select the tuning button. See Picture below.

       

      Step 3 - Select your brand (ABARTH or FIAT, both will have a selection for the 124 nested underneath). See Picture below.

       

      Step 4 -Select your model (124 SPIDER). See Picture below.

       

      Step 5 - Push the right arrow to confirm your selection.

       

      Step 6 - Select your engine and ECU model (shown below). Also note your choice of Transmission. Push the RIGHT arrow to confirm. See Picture below.

       

      Step 7 - Follow the prompts. Turn on the ignition power (For ignition power on the 124 double-tap the start button with foot off the brake, DO NOT START THE ENGINE), and select OK. When asked to "Key on and confirm." be sure to wait 5-10 seconds after turning on ignition before hitting OK to ensure all modules are powered for proper communication.

       

       

      Step 8 - EURO+DRIVE will ask if you would like to begin reading the ECU. Select "YES" and continue. See Picture below.

       

      - EURO+DRIVE will begin reading the ECU file. See Picture below.

       

      Step 9 - Once the read is complete, turn the ignition off as instructed. Select OK, and once at the main menu, disconnect from your vehicle. See Picture below.

       

      Step 10 - Take your handheld and connect to your computer or PC device. Open the EURO+DRIVE manager. See Picture below.

       

      Step 11 - Once connected, select "DOWNLOAD DATA" from the manager menu on the left hand side. See Picture below.

       

      Step 12 - Select the "START" button to begin downloading your ECU read file from the handheld. See Picture below.

       

       

      Step 13 - Once the file download is complete, select the folder location on your computer where you would like to save the file (some place you will remember). The file should be titled similar to what you see below. This will help us in file identification. See Picture below.

       

      Step 14 - After the file is saved, open your web browser and go to the EURO+DRIVE Online Portal. Login to your account. See Picture below.

       

      Step 15 - Once logged in, use the upload button (+) to upload your file. This plus button will only show up when you're in your personal folder with your name that we shared with you. Once uploaded we will receive a notification for the file upload, and begin creating your tune files. Please allow for 24-72 business hours to receive your tune files back, depending on our current volume of customers.

      To speed up this process, please ensure you are also uploading your tune request forms at the same time with all modifications listed, and any requested add ons you may have purchased with your system.

       

      Step 16 - Once your tune files have been uploaded, you will receive an email notification from the online portal. Download the tuning file to your computer. Once the file download is complete, select the folder location on your computer where you would like to save the file (some place you will remember).

       

      - The tune file format is a.USR file. This is a single zip file, but will contain all tune files and your Original file (needed to flash back to stock). These will display on the handheld screen when you go to flash the car. Only this one file needs to be loaded to the handheld in order for you to flash your ECU. The title will appear similar to what you see below.

       

      Step 17 - Plug your handheld into the computer, open the EURO+DRIVE manager, and once connected to the handheld select "UPLOAD DATA" from the manager menu on the left. See Picture below.

       

      Step 18 - Select the "START" button, and select the tune file you downloaded from the portal. See Pictures below.

       

       

       

       

      Step 19 - Once the tuning file is loaded to the handheld, you may now proceed to your vehicle and connect to the OBDII port. Once the main menu appears, select "TUNING". See Pictures below.

       

       

      Step 20 - The EURO+DRIVE will ask if you are ready to write the file. Select "YES". See Picture below.

       

      Step 21 - The EURO+DRIVE will now display all tune files stored on the device. Select the map you would like to flash to your ECU, and press the RIGHT arrow to proceed. See Pictures below.

      The original file stored in the handheld is the stock file from your vehicle. In order to flash back to stock, follow this same process but select ORIGINAL from the list.

       

       

       

      Step 22 - Turn on the ignition power, and press OK to continue. Remember to allow 5-10 seconds after turning on ignition before confirming the Key on request. This prevents miscommunications. See Pictures below. 

       

       

       

      - The tune file will now begin writing to the ECU. DO NOT disconnect the handheld for any reason.

       

      - During the writing process, it is normal to see error messages on the dash or instrument cluster during the file transfer. These will not remain once the process is complete.

       

      Step 23 - Once the write process completes, you will see this message. Press OK. See Picture below.

       

      Step 24 - Turn the ignition off, and press OK. See Pictures below.

       

       

       

      Step 25 - Turn on the ignition and press OK. See Picture below.

       

       

      Step 26 - Start your engine and press OK. See Pictures below.

       

       

      Step 27 - Now turn the ignition off and press OK. See Picture below.

       

      Step 28 - Turn on the ignition, and press OK. See Pictures below.

       

      The write process is complete. Turn the ignition off, and press OK. Then you can disconnect the EURO+DRIVE from the OBDII port.

      If the car does not start after disconnecting the handheld, disconnect the battery for an hour. This is usually caused by the car going into theft immobilizer mode. The reason this sometimes happens is due to rushing through the Key ON/OFF prompts and not giving the proper amount of time between key cycles.

       

       

       OTHER OPERATIONS:

      The EURO+DRIVE handheld is capable of reading, interpreting, and clearing CELs and DTC codes from your vehicle. If you have a check engine light, the handheld can be used to read and clear the code.

      To do this, follow the procedure below:

      Plug the handheld into the OBDII port, turn on the ignition.

      From the Main Menu, select "DIAGNOSIS":

       

      Then select "MY VEHICLE":

       

      Then select "DTC Codes":

       

      If you have already associated the handheld with your vehicle, you will go straight into communication with the ECU. Simply follow the prompts to read and clear the codes. 

      If you have not already connected to the vehicle before, you will simply need to select your make and model of car. Then proceed with the prompts.

       

       

       

      Older Post Newer Post 

      124 Spider Abarth 3rd Party Performance Data Playlist (Thanks Driven District!)
      124 ABARTH SPIDER Tuning Updates
      V4 Air Intake Dyno Testing - 124 ABARTH SPIDER
      Stock 1/4 Mile & Dyno - 124 ABARTH SPIDER
      FIAT 124 SPIDER - AFR DATA with High Flow Exhaust
      FIAT 124 SPIDER - Air/Fuel Ratio Data
      124 ABARTH SPIDER - Performance Air Intakes
      GEN 1 HANDHELD - EURO+DRIVE Flash Tune Install - Fiat 124 Spider/Abarth
      ECU Removal/Install FIAT 124 Spider

      WE CANNOT GUARANTEE THE ADVERTISED GAINS IF YOU HAVE MODS WE HAVE NOT TESTED IN HOUSE.

      NEVER DISCONNECT THE UNIT WHILE READING/WRITING, NEVER RESET THE UNIT UNTIL DIRECTED TO DO SO. RECOVERY MODE AND UNLOCK FEES MAY RESULT.

      ENGINE HP NUMBERS ARE CALCULATED FROM THE WHP NUMBERS BY OUR DYNO SOFTWARE.

      DYNO NUMBERS WILL VARY WITH CLIMATE AND DYNO. PLEASE LOOK AT PERCENTAGE GAINS FROM STOCK.

       

      Eurocompulsion cannot guarantee the success or stated power gains while using modifications not tested in house or recommended. When testing results, always follow proper dyno procedures, use appropriate fuel, and compare to vehicle specific stock deltas. Eurocompulsion is not responsible for damage caused by or incurred by other modifications or user error/installation error by user or third party. End user is responsible for all unlock fees should they be incurred due to: dealership flash over of tune file prior to flashing back to stock, user error in use of the handheld, or user reset of the handheld without authorization of Eurocompulsion. Off-Road & Race Use Only. “Not legal for sale for, or use on, pollution-controlled vehicles.” “Legal only for racing vehicles which may never be used upon a highway. Not applicable or intended for street or highway use.”

       

      The EURO+DRIVE handheld can easily be reset and memory erased so that you can transfer to another owner or another vehicle. However, failure to flash your ECU back to stock prior to selling your vehicle, selling your handheld, or bringing your car into the dealership for maintenance will lock your handheld and prevent a memory erase from being executed. In this case, you will be forced to send back your handheld and purchase a replacement handheld for $300, no exceptions.

      Customer Reviews

      Customer Reviews

      Based on 31 reviews
      100%
      (31)
      0%
      (0)
      0%
      (0)
      0%
      (0)
      0%
      (0)
      P
      Paul Dixon
      Wow

      Just flashed my 124 spider, all I can say is wow

      T
      Trevor Silvestri

      Toby was super helpful as I had a lot of dumb questions. I had some issues because of a low battery voltage and I did not know what was going on, but Toby knew immediately and we were able to remediate it with no issues. I love my tune and it really makes a big difference in the car.

      T
      Thomas Zambeno
      Prompt File, Easy to set up

      Very easy to set everything up, has detailed list of what else to install and how you can use it. Extra boost is fantastic but made it far more linear and for fuel economy, it's very handy to switch back to stock tune. Everything was very easy and very satisfied with my purchase

      D
      Donald Kneedler
      First Time.

      This device was easy to use and intuitive. The online instructions were a hit! Thanks!

      M
      Mario Beslic
      Phase 2

      I love it !

      We use cookies to improve your experience on our website. Read about how we use cookies in our Privacy Policy. By browsing this website, you agree to our use of cookies. privacy policy
      accept

      Your cart

      ×