EURO+DRIVE® DIRECT TUNING/CLONE (ABARTH/500T) - EUROCOMPULSION
EURO+DRIVE® DIRECT TUNING/CLONE (ABARTH/500T) - EUROCOMPULSION
EURO+DRIVE® DIRECT TUNING/CLONE (ABARTH/500T)
Click to zoom in

EURO+DRIVE® DIRECT TUNING/CLONE (ABARTH/500T)

ECU TUNING
$499.95
$499.95

The EURO+DRIVE® CLONE Tuning System allows you to physically swap calibrations on your ABARTH/500T. Using genuine OEM Fiat/Abarth based software, protocols and calibrations, we have increased drive-ability, power and throttle response. We are proud to have the ability to offer you the most comprehensive tuning option for your Abarth/500T. Each purchase includes a Genuine Abarth/500T Engine Control Unit (If Clone is selected) loaded with our calibration. Designed and developed for the North American Abarth and Fiat 500T.

 The EURO+DRIVE® DIRECT Tuning System is an economical solution in loading calibrations on your Abarth/500T. Using genuine OEM Fiat/Abarth based software, protocols and calibrations, we have increased drive-ability, power and throttle response. We are proud to have the ability to offer you the most comprehensive tuning option for your Abarth/500T. Each purchase includes our calibration loaded onto YOUR Engine control Module. Designed and developed in the USA.

FEATURES: 

  • Designed on the North American Abarth/500T
  • Use of Genuine OEM Software,Maps and Protocols
  • Simple 10-15 min INSTALLATION/REMOVAL
  • Preserves factory ECU/WARRANTY (if CLONE is selected)
  • Calibrations will Optimize power, drive-ability, and efficiency 
  • Unparalleled consistent, linear, & smooth power delivery
  • Calibrations will retain OEM tuning logic and ALL safety parameters
  • All factory hardware works properly/efficiently 
  • Full control over all engine parameters by utilizing true factory Calibrations
  • Specially requested Calibrations available (additional fees may apply)
  • 91oct minimum fuel requirement 
  • Strong, Reliable power where and when you need it

EURO+DRIVE® CALIBRATIONS:

  • ~154 WHP 695 F.T.
  • ~178 WHP PHASE 0 
  • ~189 WHP PHASE 1
  • ~209 WHP PHASE 2

WE CANNOT GUARANTEE THE ADVERTISED GAINS IF YOU HAVE MODS WE HAVE NOT TESTED IN HOUSE.

SUPPORTED YEARS:

  • 2012 - AVAILABLE
  • 2013 - AVAILABLE
  • 2014 AVAILABLE
  • 2015AVAILABLE
  • 2016 - AVAILABLE
  • 2017 - AVAILABLE
  • 2018 - AVAILABLE
  • 2019 - AVAILABLE

     

    Dyno Charts/Info: HERE

    Tune Requirements: HERE

     TECHNICAL INFORMATION: HERE

     

    NOTES:

    Once purchased please send your factory ECU to:

    • EUROCOMPULSION-OK
    • 10763 Sahoma Lake Road
    • Sapulpa, OK 74066 

    This applies to both Euro+Drive Clone and Direct tuning Options, you must ship your original factory ECU. Please ensure your factory ECU is packaged properly to prevent damage. For clone purchasers you will receive your factory ECU and your Clone unit upon return. Turn-around time is approx. 24hrs-72hrs. (The Epoxy requires 16hrs-24hrs to fully cure.)

    Read More
    Read Less

    Customer Reviews

    Customer Reviews

    Based on 1 review
    100%
    (1)
    0%
    (0)
    0%
    (0)
    0%
    (0)
    0%
    (0)
    P
    Paulo
    Made All the Work and Pain of Installing the Engine Upgrades Worthwhile!

    Long story short, I chose to have Eurocompulsion do a direct tune on a clone ECU for my 2015 500 Abarth A/T. I bought a cheap and exact same spec ECU for cloning purposes, and sent both my original and used ECUs to Toby so that he could do the magic. Got it back some days later, installed the cloned and tuned ECU in the car, and wow... I couldn't stop smiling.

    I chose the dual map option, non-sport as the 695tf and the sport mode as Phase 2 (I had all the required parts for that tune). The 695tf is already a massive step up from the original non-sport mode, with quicker response at low-rpm and overall more power available to use. Then, the sport mode... it is amazing! The burbles I added to the tune made it sound even better, but the responsiveness is greatly increased, and the power output is night and day compared to the original sport mode. Shifts make much more sense, and it feels like the mapping Eurocompulsion did really gets the most of out each gear. Downshifting is still fast and great-sounding, so it really is all good and no bad.

    It is up to you whether the direct tuning to your ECU or getting a clone ECU for tuning is better. For me, I wanted the peace of mind of having my original ECU untouched and as a backup, specially if I need to take the car to the service center. But, the savings might be more important to you without the clone ECU. Either way, the communication was fantastic, and I am beyond happy with the tune!

    We use cookies to improve your experience on our website. Read about how we use cookies in our Privacy Policy. By browsing this website, you agree to our use of cookies. privacy policy
    accept

    Your cart

    ×